MATERIAL COST GUIDE

Asphalt Price Per Square Foot

01 / CALCULATOR

What Is the Price of Asphalt Per Square Foot?

Asphalt material costs about $1.23 to $4.93 per square foot at a compacted thickness of 2 to 4 inches, using an example price of $100 to $200 per ton. That is material only. Enter your own thickness and your supplier's price per ton below to get an exact figure.

Calculate your material cost

Use finished, compacted thickness and your supplier's price per US ton.

02 / WEIGHT

How Many Tons of Asphalt Are in One Square Foot?

At 148 lb per cubic foot, a square foot of compacted hot-mix weighs about 12.3 lb for every inch of thickness. That gives:

Compacted thicknessWeight per sq ftTons per sq ft
1 in12.3 lb0.0062
2 in24.7 lb0.0123
3 in37.0 lb0.0185
3.5 in43.2 lb0.0216
4 in49.3 lb0.0247
5 in61.7 lb0.0308
6 in74.0 lb0.0370

To go the other way, one US ton covers about 162 sq ft at 1 inch, 81 at 2 inches, 54 at 3 inches, and 40 at 4 inches. Coverage figures are rounded down.

03 / COST CHART

Asphalt Cost Per Square Foot by Thickness

Multiply tons per square foot by the price per ton. Three example price points, so you can see how thickness and ton price interact:

Thickness@ $100/ton@ $150/ton@ $200/ton
1 in$0.62$0.93$1.23
2 in$1.23$1.85$2.47
3 in$1.85$2.78$3.70
4 in$2.47$3.70$4.93
5 in$3.08$4.63$6.17
6 in$3.70$5.55$7.40
Example material prices, computed with the formula on this page — not a market quote. Replace with your supplier's current price per ton.

Cost per square foot rises linearly with thickness. A 4-inch mat costs twice as much per square foot as a 2-inch mat at the same ton price — $2.47 against $1.23 at $100 per ton. Thickness is the single biggest lever you control.

04 / INSTALLED PRICE

Material Price vs Installed Price

The per-square-foot number most cost guides quote is the installed price, which is a different figure from material cost. Between the material cost above and a contractor's number sit four things:

  1. Base course — crushed stone, graded and compacted, before any asphalt goes down.
  2. Equipment mobilization — the paver and roller have to arrive, whether the job is 400 sq ft or 4,000.
  3. Labor and compaction — placement, rolling, and joints, usually the largest single line.
  4. Minimum load and minimum job charges — a small driveway pays almost the same delivery and setup as a large one, so the per-square-foot price climbs as area shrinks.

Published cost guides typically estimate $5 to $13 per square foot installed for driveways (NerdWallet $7–$13, Nuera $5–$12; both read November 2026), but their assumptions differ from each other and from your job. Rather than quote a national number we cannot stand behind, this page works the other way round: it takes your quote and works out what it implies per ton — see the quote check below.

05 / EXAMPLE

How Thickness Changes the Total (1,000 Sq Ft)

ThicknessTons@ $150/tonvs 2 in
2 in12.3$1,850—
3 in18.5$2,775+$925
4 in24.7$3,700+$1,850

On 1,000 square feet, going from 2 to 4 inches adds $1,850 in material alone at $150 per ton, before any base or labor change. If two quotes for the same area are nearly identical on price, ask whether both cover the same compacted thickness and the same base depth — that is usually where the difference is hiding.

06 / QUOTE CHECK

What Your Quote Implies Per Ton

Divide the quoted price per square foot by the tons per square foot for that thickness. The result is the implied price per ton — material, base, labor and all, expressed in the same unit suppliers quote in.

Quoted price@ 2 in@ 3 in@ 4 in
$4.00 /sq ft$324/ton$216/ton$162/ton
$6.00 /sq ft$486/ton$324/ton$243/ton
$8.00 /sq ft$649/ton$432/ton$324/ton

Read the table across, not down. The same $6.00 per square foot implies $486 per ton on a 2-inch job and $243 per ton on a 4-inch job — a factor of two, from thickness alone. A quote that looks expensive for a thin mat may be ordinary for a thick one, and the reverse.

Before comparing bids, ask the contractor two questions: what compacted thickness and what base depth. Without both, per-square-foot prices are not comparable.

07 / PRICE FACTORS

Five Things That Move the Price Per Square Foot

  1. Region and aggregate source — stone has to travel, so haul distance is baked into the ton price. Liquid asphalt binder is a crude-linked input, so ton prices also move with oil, not with stone alone.
  2. Season — demand peaks from late spring through summer; the same mix usually costs more in June than in December.
  3. Job size and minimum charges — small areas carry fixed delivery and setup across fewer square feet.
  4. Base preparation — new excavation, grading, and stone are separate from the asphalt line.
  5. Access and shape — narrow side yards, tight turns, and long thin strips slow the paver down.
08 / METHOD

Work It Out in Three Steps

Step 1 — Area. Length × width in feet. A 20 × 50 ft driveway is 1,000 sq ft.
Step 2 — Thickness. 3 inches = 0.25 ft.
Step 3 — Multiply.

1,000 sq ft at 3 inches, $150 per ton:

StepCalculationResult
Volume1,000 × 0.25250 cu ft
Weight250 × 14837,000 lb
Tons37,000 ÷ 2,00018.5 tons
With 5% waste18.5 × 1.0519.5 tons (rounded up)
Material cost18.5 × $150$2,775
Per square foot$2,775 ÷ 1,000$2.78

Order on the compacted number plus waste, never on a loose volume — a stockpile measured before rolling is not the tonnage you should trust. A 5% allowance on 18.5 tons is 0.925 ton, so order 19.5 tons after rounding up to the next tenth; confirm the load increment with your supplier.

09 / QUESTIONS

FAQ

How much does asphalt cost per square foot?

Material only, about $1.23 to $4.93 per square foot at 2 to 4 inches using $100–$200 per ton. At 3 inches and $150 per ton it is $2.78 per square foot. Installed prices are higher because they add base, labor, and equipment.

How many tons of asphalt do I need per square foot?

At 148 lb per cubic foot: 0.0123 tons per square foot at 2 inches, 0.0185 at 3 inches, and 0.0247 at 4 inches. Multiply by your square footage to get the tonnage.

How many square feet does a ton of asphalt cover?

About 162 sq ft at 1 inch, 81 at 2 inches, 54 at 3 inches, and 40 at 4 inches. Coverage halves each time you double the thickness.

Is a thicker layer always more expensive per square foot?

In material, yes — cost rises linearly with thickness. In a full quote, not always: fixed costs such as mobilization, delivery and minimum charges spread across fewer square feet on a small job, so a thin mat on a tiny area can carry a higher price per square foot than a thick mat on a large one.

Why is a contractor's price per square foot so much higher than the ton price?

Because the ton price covers only the mix. A quote adds crushed-stone base, grading, mobilization, placement and rolling labor, joints, and often a minimum charge. To compare, convert the quote to an implied price per ton for its stated thickness — see the quote check above. That puts it in the same unit as the material price.

Do these figures include delivery or tax?

No. Every figure here is material cost at the price per ton you enter. Whether delivery, minimum-load fees and sales tax are included varies by supplier and by state, so ask for the delivered price per ton and enter that instead.